英语翻译Description for changing the left and right position from the stepper motorWT 365.0.0.without the protection cover2.we lose this lock3.we screwed this bolt in this axis.4.we pushed the axis out .5 we pushed this guide out .6 we pushed &qu

英语翻译Description for changing the left and right position from the stepper motorWT 365.0.0.without the protection cover2.we lose this lock3.we screwed this bolt in this axis.4.we pushed the axis out .5 we pushed this guide out .6 we pushed &qu
英语翻译
Description for changing the left and right position from the stepper motor
WT 365.0.0.without the protection cover
2.we lose this lock
3.we screwed this bolt in this axis.
4.we pushed the axis out .
5 we pushed this guide out .
6 we pushed "f3" and stepper motor made a reset .
7.The position of stepper motor after the reset
8.we go in the handling of the machine .we pushed "enter"
9.we pushed "shift and F1" 
10 we arrived in the working mode .
11 we pushed the >7times .
 12 we arrived in the position for switch OFF the connector -control .
13.we go in with the password '100"
14 .we changed the connector control from "ON" to "OFF"
15.we go out with "ESC".
16 We started the machine with "F1"
17.The machine goes in the loader position.
18 we push the button" <"
19.The machine arrived in the first crimping postion
20 The plunger isn't in the correct control position.
21.To push "<"any times
22.The machines arrived in the correct control position
23To push the "emergency stop " the machine cut the air pressure.
24 we moved the cylinder A0.0.to the back side
25 The machine was in the check position.
26 we installed in the calibre in the centring bar .
27 we installed in the calibre in the centring bar
28 The calibre was in the good position in the machine .
29 we pushed down the cylinder Ao.1
30 The plunger goes in the calibre on the left side we need o,4mm and on the right side we needed 0,64mm.(We can found this in calibre description in the operating manual)

英语翻译Description for changing the left and right position from the stepper motorWT 365.0.0.without the protection cover2.we lose this lock3.we screwed this bolt in this axis.4.we pushed the axis out .5 we pushed this guide out .6 we pushed &qu
Description for changing the left and right position from the stepper motor WT 365.0.0. without the protection cover
描述步进马达WT 365.0.0.在没有护罩情况下如何改变左右位置
2. we lose this lock 松开锁扣
3. we screwed this bolt in this axis. 旋紧该轴上的螺栓
4. we pushed the axis out . 推开该轴
5 we pushed this guide out . 推开该轴套
6 we pushed "f3" and stepper motor made a reset . 推开f3和步进马达进行复位
7.The position of stepper motor after the reset复位后步进马达的位置
8. we go in the handling of the machine .we pushed "enter"进行机器的处理,推到“输入”
9. we pushed "shift and F1" 推上“移动 和 F1"
10 we arrived in the working mode . 进入工作模式
11 we pushed the >7times . 推开超过七项
12 we arrived in the position for switch OFF the connector -control .
到达关掉连接头控制的位置.
13. we go in with the password '100" 进入到密码“100”
14 .we changed the connector control from "ON" to "OFF"将连接头控制从“开启”改为“关闭”
15. we go out with "ESC". 按“ESC退出键”
16 We started the machine with "F1" 用"F1"启动机器
17.The machine goes in the loader position. 机器进入装料位置
18 we push the button"