英语翻译To take a timed count,follow these steps:1.With the Digilert 100 operating,set the Mode switch to Total.The display shows SET,the hourglass,and the most recent timing period used.The first time you use the timer,the setting is 00:01,which

英语翻译To take a timed count,follow these steps:1.With the Digilert 100 operating,set the Mode switch to Total.The display shows SET,the hourglass,and the most recent timing period used.The first time you use the timer,the setting is 00:01,which
英语翻译
To take a timed count,follow these steps:
1.With the Digilert 100 operating,set the Mode switch to Total.The display shows SET,the hourglass,and the most recent timing period used.The first time you use the timer,the setting is 00:01,which means one minute.
2.Use the + and - buttons to set the timing period.The timed period can be for 1 to 10 minutes in one-minute increments,for 10 to 120 minutes in ten-
minute increments,or for 1 to 40 hours in one-hour increments.
3.Press the Set button.The Digilert 100 starts totaling the counts it registers,and the numeric display is updated each time a count is registered.The hourglass indicator flashes during the timed period.
During the counting period,if you want to see how many minutes remain,press the Set button.The display counts down from the time setting in hours and minutes to zero.For example,if the display shows 00:21,21 minutes remain.
4.At the end of the timed period,the Digilert 100 beeps three times,and repeats the beeping several times.The number displayed is the total count.
5.To find the average dose rate for the timed period,divide the total by the number of minutes.
The average count is in counts per minute.To convert to mR/hr for
Cesium-137,divide by 1000.
6.Move the Mode switch to one of the dose rate modes to return to normal operation.
If you move the Mode switch to one of the dose rate modes while the Digilert
100 is taking a timed count,the timed count will stop.
Using The Alert
The Alert can be set in mR/hr or cpm.When using Utility Menu option #2 to switch units of measurements,the alert is reset to the default alert level of .1 mR/hr (1.0 mS/hr).Once the alert threshold is reached the beeper will sound until the alert is deactivated,or the radiation level drops below the set alert threshold.
1.To set the Alert,press the "SET" button on the end panel.The "ALERT"
icon (radiation symbol) and the "SET" icon are displayed.
2.Use the "+" and "-" buttons to adjust the display to the desired level.
3.Press the "Set" button once to retain the setting in memory.Then press it again to turn the alert mode on.The "ALERT" icon is now displayed to indicate the instrument is operating in the Alert mode.
4.To use the previous alert setting,press the set button twice.Now the alert mode is on.
5.To deactivate the Alert mode,press the "Set" button again.The "ALERT"icon is no longer displayed.

英语翻译To take a timed count,follow these steps:1.With the Digilert 100 operating,set the Mode switch to Total.The display shows SET,the hourglass,and the most recent timing period used.The first time you use the timer,the setting is 00:01,which
采取定时计数,请按照下列步骤操作：
1 .随着Digilert 100业务,设置模式开关总额.显示器显示设置,沙漏,和最新的时间期间使用.第一次使用的计时器的设置是00:01 ,这意味着一分钟.
2 .使用+和-按钮来设定的时间期限.定时期间可为1至10分钟,一分钟的增量,为10至120分钟的10 -
分钟递增,或为1至40小时一小时的增量.
3 .按下SET键.开始的Digilert共100罪状它的登记册,以及最新的数字显示是每次计数登记.沙漏指标闪烁在超时期限.
在计票期间,如果你想看看有多少分钟仍然存在,按SET键.显示倒计时的时间设置以小时和分钟为0 .例如,如果显示屏显示00:21 ,21分钟仍然存在.
4 .结束时的时间期间,发出哔哔声Digilert 100三次,重复响闹几次.数字显示的总数.
5 .要查找的平均剂量率的时间期间,总的鸿沟的分钟数.
平均计数在每分钟.转换为先生/小时的
铯-137 ,除以1000 .
6 .移动模式切换到一个剂量率模式,恢复正常作业.
如果您移动模式切换到一个剂量率模式,而Digilert
100正在采取定时计数,定时计数将停止.
使用警报
警报可以设置在MR /小时或每千次展示.当使用工具菜单选项＃ 2开关单位测量,警报被重置为默认的警戒级别的0.1先生/小时（ 1.0女士/小时） .一旦警报阈值将达到蜂鸣器的警报声,直至停用,或辐射水平低于设定警报阈值.
1 .要设置警示,按“设置”按钮结束小组.在“警告”
图标（辐射象征）和“设置”图标的显示.
2 .使用“ + ”和“ - ”按钮来调整显示器的理想水平.
3 .按下“设置”按钮后,保留在内存中的设置.然后按下它再次把警戒模式.在“警告”图标现在显示说明文书作业的预警模式.
4 .使用前提醒设置,按SET键两次.现在的警戒模式上.
5 .解除警报模式,按“设置”按钮.在“警告”的图标不再显示.