ansys计算时出现 The value of UZ at node 11 is 4.907789514e19.

ansys计算时出现 The value of UZ at node 11 is 4.907789514e19. 在ansys中有关非线性计算时,如何设置收敛值,计算时出现的警告,如何处理呢The calculated reference MOMENT CONVERGENCE VALUE = 1.17562885E-08 is less than 1E-2 a threshold zero,A value of 1E-2 or specified MINREF is used.Check ansys计算出现以下错误提示,请问如何处理?TB,MISO table for material 1 at temperature 373 has a tangent slope value less than zero. ansys运算时出现的错误出现了这个错误The value of UY at node 8014 is 653136370.It is greater then the current limit of 1000000.This generally indicates rigid body motion as a result of an unconstrained model.Verify that your model is pro ANSYS非线性分析计算时,为什么没有收敛追踪图出现 ansys 中加载重力加速度时,加了约束还出现如下问题,其原因有哪些及解决方案.The value of UZ at node 2158 is 236632696.It is greater than the current limit of 1000000.This generally indicates rigid body motion as a result of 使用ANSYS时出现an error occurred while attempting to open the results file怎么办呀 ansys定义边界条件时出现这种情况怎么办 下面是ansys仿真时出现的问题怎么解决?the value of temp at node 101 is 3.024098078E+14.it is greater thanthe current limit of 1000000.this generally indicates rigid body motion as a result of an unconstrained model.verify that your model ANSYS WORKBENCH静力分析总是出现：an error occurred while starting the ANSYS solver module,最郁闷的是第二天机子重启后计算不出现这个问题了,可我什么都没改过呀? ansys疲劳分析,输入计算命令后无法计算,急,最近在做ansys疲劳分析,下列命令做到最后疲劳分析时,都会出现问题,问题提示为：N values missing,out of order,non-positive.The FTCA command is ignored大家帮忙看 Ansys计算钢桁架时出现错误信息The degree of freedom solution is not available,The PRNSOL command isAnsys计算钢桁架时出现错误信息The degree of freedom solution is not available,The PRNSOL command is ignored.该怎么解决? ansys疲劳分析分析时,在最后一步输入命令后,无法计算最近在做ansys疲劳分析,下列命令做到最后疲劳分析时,都会出现问题,问题提示为：N values missing,out of order,non-positive.The FTCA command is ignored大 matlab运行时,lsqcurvefit出现问题,出现问题提示如下：Local minimum possible.lsqcurvefit stopped because the final change in the sum of squares relative to its initial value is less than the selected value of the function tolerance.Optim ansys疲劳分析,无法计算最近在做ansys疲劳分析,下列命令做到最后疲劳分析时,都会出现问题,问题提示为：N values missing,out of order,non-positive.The FTCA command is ignored大家帮忙看看这个命令流问题出 为什么用erdas进行重编码时出现Data value out of the range of LUT错误提示? Value creation failed at line 开机时出现的! ansys如何计算离心力