icem 网格 提问 cfd谁能解决一下 这里的 spacing 1 spacing 1是 怎么回事 还有就是 ratio 是增长速率 还是斜率, Nodesspecifies the number of nodes along the edge.The number may be modified using the up and down arrows or by

来源：学生作业帮助网 编辑：六六作业网 时间：2025/01/04 15:48:33
icem网格提问cfd谁能解决一下这里的spacing1spacing1是怎么回事还有就是ratio是增长速率还是斜率,Nodesspecifiesthenumberofnodesalongtheed

icem 网格 提问 cfd谁能解决一下 这里的 spacing 1 spacing 1是 怎么回事 还有就是 ratio 是增长速率 还是斜率, Nodesspecifies the number of nodes along the edge.The number may be modified using the up and down arrows or by
icem 网格 提问 cfd
谁能解决一下 这里的 spacing 1   spacing 1是 怎么回事 还有就是 ratio 是增长速率 还是斜率,
 
Nodes
specifies the number of nodes along the edge.The number may be modified
using the up and down arrows or by entering a number in the field.
Mesh law
Allows you to select one of several bunching laws described in detail in Bunching Laws.
Spacing
specifies the spacing of the first node from the beginning of the edge (first
cell height).When an edge is selected,an arrow appears along the edge.
Spacing 1 refers to the parameters
at the beginning end of the arrow,and Spacing
2 refers to the edge end where the arrow is pointing,as shown
in Figure 78.You may modify
the values of the parameters available for the selected Meshing law.The actual
values will differ from the requested values only if the requested values cannot
be met.For example,if the Edge length is 10 units,and you specify an initial
spacing of 6 on both sides and 11 nodes along the edge,the system will simply
space the nodes evenly,giving an initial spacing of 1 and a spacing ratio of
1.
Ratio
is the growth rate from one cell height to the next.Ratio 1 refers to the parameters at the beginning
end of the arrow,and Ratio 2
refers to the edge end where the arrow is pointing,as shown in the figure
below.

icem 网格 提问 cfd谁能解决一下 这里的 spacing 1 spacing 1是 怎么回事 还有就是 ratio 是增长速率 还是斜率, Nodesspecifies the number of nodes along the edge.The number may be modified using the up and down arrows or by
你选择一个edge后那个edge上不是有个箭头吗,靠近箭头,顺着箭头方向的那个端点就是spacing1的起点,另外一个就是spacing2的起点了,ratio是生长率,也就是你网格节点由密变疏的快慢.

icem 网格 提问 cfd谁能解决一下 这里的 spacing 1 spacing 1是 怎么回事 还有就是 ratio 是增长速率 还是斜率, Nodesspecifies the number of nodes along the edge.The number may be modified using the up and down arrows or by icem中负网格怎么解决ICEM CFD 中划分了网格,导入CFX中求解时出现负网格,怎么才能解决,明白的请详细说明原因及解决办法, icem-cfd 怎么看网格数量?用icem-cfd打网格后,怎么看网格数量?用什么方法,或者点哪个按钮?求指教, icem cfd 中为什么画网格时只有个一个物体有网格如图 如何用icem cfd划分2D 三角形的结构网格 麻烦提供一些思路 用ICEM-CFD软件划分流体网格,怎么只对实体之外的流体画网格啊? icem cfd和ansys,ansys icem cfd的关系 icem cfd如何添加 边界条件 ANSYS 14.0中怎么找不到ICEM CFD? ICEM cfd 研究汽车空气动力学怎么样 icem cfd 中材料点是什么意思初学icem cfd,不知道icem中材料点是什么意思,有什么作用? 你会用ICEM CFD 做前处理吗? 想请教你关于fluent中网格的interface设置的问题?在gambit/ICEM CFD中,上下两个区域分别用不同的网格形式建立网格,中间两个重合的面a1和a2（大小不一样,假定a2>a1）都定义成“interface”要求：1、 你好,想请教你关于fluent中网格的interface设置的问题?在gambit/ICEM CFD中,上下两个区域分别用不同的网格形式建立网格,中间两个重合的面a1和a2（大小不一样,假定a2>a1）都定义成“interface”要求 ICEM里面设置一下就可以自动划分网格,为什么要用块?用块只是因为网格质量好吗?还是必须用块才能划分得了?如图,长方形一面接三个小圆柱,应该怎样划分网格呢? 我用workbench建完模之后,如何导入ICEM画网格?本人初学ICEM和workbench icem 如何对多个part进行网格划分 关于solidworks建模如何导入ICEM画网格的问题?