求助人工翻译（中翻英）急谢谢!我们面临一个XX问题,程序里面设置800N,可是测试时却只能达到一半或不到一半的力!我们把XX校验后,程序里面设置800N,测试时也能达到800N,在做这个测试时还会
来源：学生作业帮助网 编辑：六六作业网 时间：2025/01/12 06:27:40
求助人工翻译（中翻英）急谢谢!我们面临一个XX问题,程序里面设置800N,可是测试时却只能达到一半或不到一半的力!我们把XX校验后,程序里面设置800N,测试时也能达到800N,在做这个测试时还会
求助人工翻译（中翻英）急谢谢!
我们面临一个XX问题,程序里面设置800N,可是测试时却只能达到一半或不到一半的力!我们把XX校验后,程序里面设置800N,测试时也能达到800N,在做这个测试时还会出现一个问题只拉一次出现中断!（注意：1.过一段时间XX就要校验一次 2.每一次校验以后程序里的两个数据必须放大以后才不会出现 报错信息） 请问是什么原因造成的?软件问题还是其它问题?
求助人工翻译（中翻英）急谢谢!我们面临一个XX问题,程序里面设置800N,可是测试时却只能达到一半或不到一半的力!我们把XX校验后,程序里面设置800N,测试时也能达到800N,在做这个测试时还会
We are facing a XX problem (a problem of XX),the settings are 800N inside the program,but the pulling force can reach half or even less in the test.After checking of this XX and with same settings of 800N inside,it can reach 800N in the test.But there is another problem in the test; it will be interrupted after one time pulling.(Note:1st,after a while,it has to be checked again; 2nd,after every checking,the two data in the program must be amplified,otherwise there will be error messages) What is the problem of this?Is it the software problem or something else?
We face a problem of XX program in setting 800 n, but when the test is only half or less than half of the force! XX after check, we put the program Settings inside 800 n, the test also can reach 800 n...
全部展开
We face a problem of XX program in setting 800 n, but when the test is only half or less than half of the force! XX after check, we put the program Settings inside 800 n, the test also can reach 800 n, when doing the test there will be a problem just pull a interruptions! XX (note: 1. Over a period of time to check a 2. Every time after check two data in the program must be magnified later won't appear error messages) could you tell me what reason be cause? Software problem or other problems?
收起
We are faced with aproblem of XX,inside the procedureset 800N,butthe testcan only reachhalf orless than half theforce!We put theXXcheck,inside the procedureset 800N,can achievethe 800N test,inthis tes...
全部展开
We are faced with aproblem of XX,inside the procedureset 800N,butthe testcan only reachhalf orless than half theforce!We put theXXcheck,inside the procedureset 800N,can achievethe 800N test,inthis testwill be aproblem onlyoneinterruption!(Note:1over a period oftime XXwillcheckevery 2everycheckaftertwo datain the programmust beamplifiedbeforedoes not appearerror message)what is thereason?Softwareproblems or other issues?
收起