英语翻译Problem 5:Device shows NO GSM when bootingThe radio stack is screwed,you don't get GSM signal and the phone says unknown SIM status Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1) Here is h

英语翻译Problem 5:Device shows NO GSM when bootingThe radio stack is screwed,you don't get GSM signal and the phone says unknown SIM status Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1) Here is h
英语翻译
Problem 5:Device shows NO GSM when booting
The radio stack is screwed,you don't get GSM signal and the phone says unknown SIM status
Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1)
Here is how to fix it:
METHOD 1
1.Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2.Put your Hermes in bootloader mode
3.Connect device to computer using USB cable.
4.Open mtty.exe and select USB port,then connect.
5.Hit enter twice,you will see the "USB>" prompt.
6.
Type the following commands (do not copy paste!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7.If the password does not work,try password BsaD5SeoA
8.Reset your phone and put it back in bootloader mode
9.If your bootloader version is different than 1.04 then Flash Bootloader version 1.04 (if you can't flash the bootloader version 1.04 (for what ever reason) and you have KITL enabled Rom,then there is final solution - PB_KITL_HERMES))
10.Flash the patched radio used to simunlock the Hermes
11.Your phone should be alive again :)
METHOD 2
Also,Ive found that Hard-Reseting the device restores GSM.
1.Remove the battery
2.wait 10 second
3.Re-insert Battery
4.Turn the device on
5.Watch for "NO GSM" on boot
6.if you see it.Return to step 1.(sometimes you have to do it up to 20 times)
If you see two lines of text flash up instead of 'No GSM' it means the GSM is functioning.For me this restored my radio in just 4 tries.
This ONLY works if your radio is NOT corrupted,but if you tried to updgrade and stalled between 0% and 15% of the GSM upgrade,it depends on the radio version you were trying to flash.But it's worth a try,the only downside is if your phone crashes,it will more than likely boot up with 'No GSM' so you'll have to do all over again.

英语翻译Problem 5:Device shows NO GSM when bootingThe radio stack is screwed,you don't get GSM signal and the phone says unknown SIM status Device won't start after trying to unlock it with HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1) Here is h
问题5：启动时机器显示无GSM信号
射频协议栈被破坏,无法获取GSM信号,并且手机显示SIM卡状态未知.除非用HTC Universal Unlocker(HTC_Uni_SIM_Unlock_v1)解锁,否则机器不会开机.
以下说明如何修复：
方法1
1.电脑上右键单击同步图标->connection settings,取消“allow USB connections”的选中状态.
2.把你的Hermes置为引导模式
3.用USB线把机器与电脑连接.
4.打开mtty.exe,选择USB端口,然后连接
5.按两次回车键,你会看到“USB>”提示符
6.
输入以下命令（请不要直接拷贝粘贴!）
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7.如果密码错误,尝试密码?BsaD5SeoA
8.重启手机,并设置成引导模式
9.如果引导程序不是版本1.04,那么下载引导程序1.04（不管什么原因,如果你不能下载引导程序1.04,并且你使用的是KITL有效的存储器,那么有一个最终解决方案-PB_KITL_HERMES）
10.刷入sim卡射频补丁,为Hermes解锁
11.你的手机现在应该是救活了 ：）
方法2
同时,我发现硬启动可以恢复GSM
1.去掉电池
2.等待10秒钟
3.重新插入电池
4.开机
5.观察开机时“NO GSM”提示
6.看到之后,回到步骤1（有时候你可能反复操作20次才行）
如果你看到不是“No GSM”而是另外两行文字显示的话,就意味GSM开始工作了.
我就是这么尝试4次成功恢复射频的.
这种方法只是针对你的射频没有损坏才有效,但是如果你给GSM升级的时候只升级到0%到15%就不一定了,具体的比例取决于你升级的射频版本.不过还是值得尝试哦!最多是手机无法启动,这可比显示“No GSM”比例高.所以你就一遍一遍试吧!

Problem 5: Device shows NO GSM when booting
问题5：当硬件启动时没显示（接受）GSM（信号）
The radio stack is screwed, you don't get GSM
广播屏幕显示你没有得到GSM信号
signal and the phone says unknown SIM status
...

全部展开

Problem 5: Device shows NO GSM when booting
问题5：当硬件启动时没显示（接受）GSM（信号）
The radio stack is screwed, you don't get GSM
广播屏幕显示你没有得到GSM信号
signal and the phone says unknown SIM status
手机说你的硬件不能开启你的SIM卡在你尝试将手机
Device won't start after trying to unlock it with
后面的SIM卡锁锁上之后
HTC Universal Unlocker (HTC_Uni_SIM_Unlock_v1)

Here is how to fix it:
修理方法
METHOD 1
1. Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2. Put your Hermes in bootloader mode
3. Connect device to computer using USB cable.
4. Open mtty.exe and select USB port, then connect.
5. Hit enter twice, you will see the "USB>" prompt.
6.
Type the following commands (do not copy paste!!!)
USB> password 0000000000000000
USB> set 1e 1
USB> erase a0040000 c80000
USB> erase a0cc0000 c80000
USB> erase a1940000 640000
USB> set 1e 0
7. If the password does not work, try password ?BsaD5SeoA
8. Reset your phone and put it back in bootloader mode
9. If your bootloader version is different than 1.04 then Flash Bootloader version 1.04 (if you can't flash the bootloader version 1.04 (for what ever reason) and you have KITL enabled Rom, then there is final solution - PB_KITL_HERMES))
10. Flash the patched radio used to simunlock the Hermes
11. Your phone should be alive again :)
METHOD 2
Also, Ive found that Hard-Reseting the device restores GSM.
1. Remove the battery
2. wait 10 second
3. Re-insert Battery
4. Turn the device on
5. Watch for "NO GSM" on boot
6. if you see it. Return to step 1. (sometimes you have to do it up to 20 times)
If you see two lines of text flash up instead of 'No GSM' it means the GSM is functioning. For me this restored my radio in just 4 tries.
This ONLY works if your radio is NOT corrupted, but if you tried to updgrade and stalled between 0% and 15% of the GSM upgrade, it depends on the radio version you were trying to flash. But it's worth a try, the only downside is if your phone crashes, it will more than likely boot up with 'No GSM' so you'll have to do all over again
其余没意义，估计你的刷机被你刷坏了

收起