注塑机参数,中英对照翻译2.1 - FORCE CLOSURE: BETWEEN 80 AND 90 TONS.2.2 - LINEAR AND MOVES TO SUPPORT BOARD MOBILE2.3 – Screw L/D ratio: 18 to 22 mm2.4 - VOLUME MAXIMUM INJECTION: MINIMUM 170 CM3 2.5 - MAXIMUM CAPACITY OF INJECTION: MINIM

注塑机参数,中英对照翻译2.1 - FORCE CLOSURE: BETWEEN 80 AND 90 TONS.2.2 - LINEAR AND MOVES TO SUPPORT BOARD MOBILE2.3 – Screw L/D ratio: 18 to 22 mm2.4 - VOLUME MAXIMUM INJECTION: MINIMUM 170 CM3 2.5 - MAXIMUM CAPACITY OF INJECTION: MINIM
注塑机参数,中英对照翻译
2.1 - FORCE CLOSURE: BETWEEN 80 AND 90 TONS.
2.2 - LINEAR AND MOVES TO SUPPORT BOARD MOBILE
2.3 – Screw L/D ratio: 18 to 22 mm
2.4 - VOLUME MAXIMUM INJECTION: MINIMUM 170 CM3
2.5 - MAXIMUM CAPACITY OF INJECTION: MINIMUM 160 G
2.6 - CAPACITY PLASTIFICAÇÃOEM PS: MIN 12 G / S
2.7 - CURRENT INJECTION UNIT: MINIMUM 300 MM
2.8 - MAXIMUM SPEED OF INJECTION: MINIMUM 60 CM3/Sec
2.9 - MÁXIMUM THREAD SPEED: MINIMUM 260 RPM
2:10 - PLASTIFICADORA THREAD DIAMETER: 35 MM MIN
2:11 - ZONE HEATING: MINIMUM 04
2:12 - COURSE UNIT INJECTION: MINIMUM 300 MM
2:13 - COURSE OPENING UP: MINIMUM 350 MM
2:14 - MAIN ENGINE: MIN 15 hp
2:15 - PRESSURE INJECTION: MINIMUM BAR 1600
2:16 - HYDRAULIC PRESSURE OF WORK: MINIMUM BAR 160
2:17 - MAXIMUM MOLD: MINIMUM 360 MM
2:18 - MINIMUM HEIGHT OF MOLD: UP TO 130 MM
2:19 - PLATES SIZE: MINIMUM 520 MM
2:20 - PLATE FIXED AND MOBILE WITH RIP " T " FOR
Lashing the CAST
2:21 - SPACE BETWEEN COLUMNS: MINIMUM 350 MM
2:22 - HYDRAULIC PULLER
2:23 - TRAVEL EXTRACTOR: MINIMUM 90 MM
2:24 - AIR EXTRACTION: MINIMUM 04 ITEMS
INDEPENDENT

注塑机参数,中英对照翻译2.1 - FORCE CLOSURE: BETWEEN 80 AND 90 TONS.2.2 - LINEAR AND MOVES TO SUPPORT BOARD MOBILE2.3 – Screw L/D ratio: 18 to 22 mm2.4 - VOLUME MAXIMUM INJECTION: MINIMUM 170 CM3 2.5 - MAXIMUM CAPACITY OF INJECTION: MINIM
2.1力封闭：80至90吨.
2.2线性和支持移动板移动
2.3–螺杆长径比：18到22毫米
2.4卷的最大注：最小170 cm3
2.5注射最大容量：最小160克
2.6容量plastificaÇÃOEM PS：至少12克/秒
2.7 -注入电流单位：最小300毫米
2.8注射最大速度：最小60立方厘米/秒
2.9米Á最大线速度：最小260转
2:10 - plastificadora螺纹直径：35毫米分钟
11区加热：最小04
2:12 -课程单元注射：最小300毫米
2:13课程开放：最小350毫米
2:14 -主发动机：15分钟,惠普
注：最小2:15压力1600 bar
16 -工作液压：最低杆160
2:17 -最大模具：最小360毫米
2:18最小高度模具：可达130毫米
2:19板尺寸：最小520毫米
2:20板固定和移动的RIP,“T”
绑扎铸造
柱间2:21空间：最小350毫米
22 -液压拉马
2:23旅行器：最小90毫米
2:24空气提取：至少04项
独立的