英语翻译1.Bracelet Design and Outlay.2． chargingThe Bluetooth bracelet comes with a built in rechargeable battery.Before using the bracelet for the first time please charge the battery fully (Approximately 6 hour charge)2.1 How to chargeTo char

英语翻译1.Bracelet Design and Outlay.2． chargingThe Bluetooth bracelet comes with a built in rechargeable battery.Before using the bracelet for the first time please charge the battery fully (Approximately 6 hour charge)2.1 How to chargeTo char
英语翻译
1.Bracelet Design and Outlay.
2． charging
The Bluetooth bracelet comes with a built in rechargeable battery.Before using the bracelet for the first time please charge the battery fully (Approximately 6 hour charge)
2.1 How to charge
To charge the bracelet please plug the appropriate end in to the bracelet charge port on the bracelet and the USB end either into a computer or the wall adapter provided.
2.2 Normal Charging Time
The bracelet will normally take 2 hours charge from completely flat.When the battery is fully charged the bracelet will automatically stop charging.
2.3 Charge Indication
The LED light will be solid red when battery is charging.Once the battery is fully charged the light will turn off .
2.4 Standby time
Up to 60 hours standby time,note that the stand by time is effected by how often the bracelet vibrates and flashes.
2.5 Low Battery Notification
When the battery is running low the LED will blink red and the bracelet will beep/vibrate once a minute.When this occurs please charge the bracelet to ensure greater battery life.
3.Turning the Bracelet OFF/ON
To turn the bracelet on old down the main btton for 2 seconds until the LED flashes.To turn the bracelet off hold the main button down until the LED turns off.
4.Prairing Bracelet with phone
To pair the bracelet with your phone:
Keep bracelet within 1 metre of your phone
Ensure bracelet is turned off to begin
Hold the main button down for 4 seconds until the LED light starts flashing green and red.
Search for the device on your phone,it will come up with the name “Bracelet”
Press yes to pair the device.
It will then ask for a pass code enter “0000”
Press yes to connect the device and authorise it .
The bracelet should now be paired with your phone.
5.Linking Bracelet with phone
When the bracelet is turned back on,depending on your phone it should re-link automatically.
To re-link the bracelet with the phone manually go to the Bluetooth menu on your phone select the bracelet in thin list and choose the connect with device option.Ensure that your bracelet is now turned on .You may have to re-enter the pass code.
6.Bracelet Operation
The bracelet will vibrate and the LED will flash blue when you have an incoming call.
7.To Reset Bracelet
You may want to reset the bracelet back to the original factory settings,this function clears all current pairings with bracelet:
Ensure that bracelet is switched of
Continually keep pressing the main button until LED flashes blue and red .
Release the main button
Hold main button until it buzzes 2 times.
Connect the power charge cable to the bracelet and charge for a few seconds.
The bracelet will now turn off and all parings have been cleared.

英语翻译1.Bracelet Design and Outlay.2． chargingThe Bluetooth bracelet comes with a built in rechargeable battery.Before using the bracelet for the first time please charge the battery fully (Approximately 6 hour charge)2.1 How to chargeTo char
1.蓝牙设备的设计与开支.
2充电
机器内建可充电池,首次使用必须将机器充满电（大约充六个小时）.
2.1如何充电
充电时请将机器正确连接好,一头插入机器充电接口,另一头插入USB插口内（电脑或专用电源适配器的USB口）.
2.2一般充电时间
一般两个小时就会完全充电完毕,充电完成后机器自动停止充电.
2.3充电指示
充电时LED灯显示为红色直亮,充电结束时充LED灯熄灭.
2.4待机时间
最长60个小时待机时间,具体时间取决于机器振动和闪烁次数和频率.
2.5低电压显示
当电池电量快用完时,LED灯以红灯闪烁且机器每分钟响一次或振动一下.如有以上现象请尽快充电以确保电池不受损坏.
3如何开机
将机器主开关往下拨保持两秒以上直至LED灯闪烁即开机,关机时保持主开关向下两秒以上直至LED灯熄灭.
4如何将机器与手机连接
连接时请保持机器与手机1米的距离内,确保机器为关机状态,按住机器主开关向下保持四秒以上至LED灯闪烁绿色和红色.在你的手机上搜索蓝牙设备,你的手机会发现“BRACELET”的名字,点“YES”连接设备.然后显示要输入密码,输入“0000”,然后点YES,机器将自动和手机连接.
5如何重新联接
重新联接时要将手动将手机调至蓝牙功能为开的状态,然后选择设备,确保你的蓝牙机器为打开状态,还要重新输入密码“0000”
6如何操作蓝牙设备
当有打入电话时,蓝牙设备即振动和闪烁蓝光
7如何重置蓝牙设备
如想重置蓝牙设备为出厂设置,注意此操作将已配对操作清除掉,长按主开关至LED灯闪烁蓝色和红色,松开主开关,保持主开关响两次,联接充电线给蓝牙设备充电数秒,蓝牙设备将关机,所有配置将被清除.操作即完成.