英语翻译Adding Pallets Touch,press or set the following Comments The system supports a maximum of two pallets.If new pallet data is to be entered to the Pallet Viewer,the user must first delete a pallet.See 'Deleting Pallets'.From the following m
来源:学生作业帮助网 编辑:六六作业网 时间:2025/02/03 09:08:28
英语翻译Adding Pallets Touch,press or set the following Comments The system supports a maximum of two pallets.If new pallet data is to be entered to the Pallet Viewer,the user must first delete a pallet.See 'Deleting Pallets'.From the following m
英语翻译
Adding Pallets
Touch,press or set
the following
Comments
The system supports a maximum of two pallets.If new pallet data
is to be entered to the Pallet Viewer,the user must first delete a
pallet.See 'Deleting Pallets'.
From the following menu,enter Pallet ID data and Location data.
The tab buttons may be used to access each field.
+111
1
Also,touch to activate the 'Pallet Present' status.
Enabling 'Pallet Present' confirms to the system that the pallet
is physically present.
If you are not using pallet offsets leave X,Y and Z values at 0 and
touch OK to return to the pallet menu.
If you are using pallet offsets,continue below:
If active tool edge finder radius
is in the tool table press "Get
Edge Finder Offset".If not,
touch to highlight field and en-
ter edge finder radius value.
Page 2--118
Cincinnati Machine 91204265--001
Menu
Adding Pallets
Touch,press or set
the following
Comments
Enter Spindle speed and
direction.
(Data Entry)
Cycle Start
Position edge finder to setup 2.
0
10
90
--
20
30
80
70
+
40
60
50
Use Handwheel and small
increments to manually jog
axes until the edge finder tool
registers to set X axis.
Touch to select side position
then OK.
OK
0
10
90
--
20
30
80
70
+
Use Handwheel and small
increments to manually jog
axes until the edge finder tool
registers to set Y axis.
40
60
50
Cincinnati Machine 91204265--001
Page 2--119
英语翻译Adding Pallets Touch,press or set the following Comments The system supports a maximum of two pallets.If new pallet data is to be entered to the Pallet Viewer,the user must first delete a pallet.See 'Deleting Pallets'.From the following m
加入托盘触摸,新闻或是设定了以下的评论语调责方的立场,然后确定.好托盘冲抵观众菜单将显示与托盘加选定.第2页-- 120辛辛那提机床91204265 -- 001菜单定位托盘触摸,新闻或是设定了以下几点意见:图形下面是实物托盘位置.在这个例子中,托盘# 111是定位在1月的机器.托盘# 222是定位在2月托盘兑换.3位置总是确定的位置空缺.在这个例子中,3位置是在负荷站1月托盘兑换.机器将派出3位置,如果两个托盘占托盘兑换地点.谨慎设置托盘位置为零 换马或托盘位置号码与其他托盘会造成数据不一致造成了警报系统.如有必要,使用选项键选择的位置占领了托盘.然后触摸按钮托盘(即:# 111或222 # )所占用的位置.重复的程序进行了第二盘.如果您选择apallet locationalready definedby分外托盘,托盘数据交换选择选单.这份菜单是通过多--托盘系统装置,是不适应这两个托盘上的应用.见谨慎.托盘记录表明托盘已在位置1 ( ID号码111 ) .什么是实际的位置,这盘没有可用的机器.设置位置为0位置号码是本末倒置.设定ID号码111外景@ 2 .按下取消按钮,并确定了一些位置的托盘位置如上所述.辛辛那提机床91204265 -- 001页2 -- 121菜单添购机器托盘序列摸 新闻或是设定了以下意见与看法托盘积极进行如下重新托盘加工顺序:注:如果一个托盘图标不显示,这不是身(页图标显示) .让托盘图标 触摸启动'托盘本'的选择托盘经编辑设施的看法托盘菜单.承担以下托盘秩序.你想作托盘# 222首加工秩序.使用这些按钮来选择第一,即:222加工秩序已经有所改变.看到托盘# 111 ,现在是第二次在加工过程中.第2页-- 122辛辛那提机床91204265 -- 001