英语翻译the tensile properties of lm 25 alloy at elevated temperatures are influenced by the condition(heat treatment)of the castings and the duration at the elevated temperature.on short term testing e.g.30 minutes at temperature,the properties

英语翻译the tensile properties of lm 25 alloy at elevated temperatures are influenced by the condition(heat treatment)of the castings and the duration at the elevated temperature.on short term testing e.g.30 minutes at temperature,the properties
英语翻译
the tensile properties of lm 25 alloy at elevated temperatures are influenced by the condition(heat treatment)of the castings and the duration at the elevated temperature.on short term testing e.g.30 minutes at temperature,the properties fall only slowly and uniformly up to about 200 deg c,at which temperature the strength of LM25-TF is reduced by about 20%.very prolonged heating,e.g.10,000hours ,results in a sharp loss of strength at about 135 deg c .at 200 deg c the strength of LM25-TF is less than half of that at room temperature.there is therefore no advantage to be gained by heat treatment,if the component is to be used at temperatures above about 130 deg c,for extended periods of time
数蚂蚁 21:57:20
the tensile properties of lm 25 alloy at elevated temperatures are influenced by the condition(heat treatment)of the castings and the duration at the elevated temperature.on short term testing e.g.30 minutes at temperature,the properties fall only slowly and uniformly up to about 200 deg c,at which temperature the strength of LM25-TF is reduced by about 20%.very prolonged heating,e.g.10,000hours ,results in a sharp loss of strength at about 135 deg c .at 200 deg c the strength of LM25-TF is less than half of that at room temperature.there is therefore no advantage to be gained by heat treatment,if the component is to be used at temperatures above about 130 deg c,for extended periods of time .
好象是说铸造金属的条件啊,温度什么的.

英语翻译the tensile properties of lm 25 alloy at elevated temperatures are influenced by the condition(heat treatment)of the castings and the duration at the elevated temperature.on short term testing e.g.30 minutes at temperature,the properties
高温条件下LM-25合金的拉伸性能受同等条件下铸件及时间情况（热处理）的影响.短时测试如：在200度环境下30分钟内,其性能仅缓慢匀速下降,同一温度下,LM25-TF的强度减少到百分之二十.长时测试如：在135度环境下10000小时后,其强度会骤然降低.在200度环境下,LM25-TF的强度仅为室温的一半.因此,如果被锻造部分被长时间用于130度以上的环境中,热处理则没有任何有益之处.

拉伸性能的流明25合金在高温下受条件（热处理）的铸件和持续时间，在高温下。短期测试eg30分钟，温度，性能下降缓慢均匀上升至约200度ç ，在温度的实力LM25因子减少了20 ％左右。很长时间加热， eg10000hours ，结果在一个急剧的强度损失约135度ç 。为200度c该强度的LM25因子是不到一半，在室温。因此，有没有优势取得了热处理，如果部分是被用来在温度...

全部展开

拉伸性能的流明25合金在高温下受条件（热处理）的铸件和持续时间，在高温下。短期测试eg30分钟，温度，性能下降缓慢均匀上升至约200度ç ，在温度的实力LM25因子减少了20 ％左右。很长时间加热， eg10000hours ，结果在一个急剧的强度损失约135度ç 。为200度c该强度的LM25因子是不到一半，在室温。因此，有没有优势取得了热处理，如果部分是被用来在温度超过130度C的长时间的拉伸性能的流明25合金在高温下受条件（热处理）的铸件和持续时间，在高温下。短期测试eg30分钟，温度，性能下降缓慢均匀上升至约200度ç ，在温度的实力LM25因子减少了20 ％左右。很长时间加热， eg10000hours ，结果在一个急剧的强度损失约135度ç 。为200度c该强度的LM25因子是不到一半，在室温。因此，有没有优势取得了热处理，如果部分是被用来在温度超过130度C的长时间。

收起